Page 1 of 4 1234 LastLast
Results 1 to 10 of 44

Thread: Test Dungeon with Torstans Tiles.

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Administrator Redrobes's Avatar
    Join Date
    Dec 2007
    Location
    England
    Posts
    7,244
    Blog Entries
    8

    Post Test Dungeon with Torstans Tiles.

    Since we collectively sorted out Torstans tiles on ViewingDale I thought Id have a play to see what I could do with them. So I have used quite a few of them in this map. The only non Torstan tiled bit is that I have applied a mud coloured texture between all the rooms but thats it. Everything else is from his set. Since its just a test this is a finished map.
    Attached Images Attached Images

  2. #2
    Community Leader Facebook Connected torstan's Avatar
    Join Date
    Jul 2007
    Posts
    4,199

    Post

    Looks good. How easy/hard was it to put together? I'm certainly interested in suggestions you have for improvement.

  3. #3
    Community Leader Facebook Connected Steel General's Avatar
    Join Date
    Jun 2008
    Location
    Ft. Wayne, IN
    Posts
    9,530

    Default

    That came out quite nicely.
    My Finished Maps | My Challenge Maps | Still poking around occasionally...

    Unless otherwise stated by me in the post, all work is licensed under a Creative Commons Attribution-Noncommercial 3.0 United States License.



  4. #4
    Administrator Redrobes's Avatar
    Join Date
    Dec 2007
    Location
    England
    Posts
    7,244
    Blog Entries
    8

    Post

    Thanks, I thought it looked alright too and it was pretty easy to put stuff together. Its a bit fiddly and could do with grouping bits together into a large selection of rooms and corridors etc but I can do that no problem. I found myself reusing the corners and walls a lot.

    The only odd bit is that there's two sets of walls, one with the stones on the grid and one with the stones to the side of the grid. I made most of the map with the stones on the grid but when I got to the right hand side and put in the stairs going down then the stairs are full width so you have to switch to stone on side of grid and fill in with stairs in between. I'm guessing that you designed it so that you stick with one or the other but I found that you need to switch to make it work out. I don't think that the issue can be avoided either.

    To make the mud texture I took the final map and saved out a big copy then just edited that map into a black and white mask, blurred it a bit and used it as an alpha transparency with a mud texture color image. Then sat it back on top. So that took just a few minutes too.

  5. #5
    Community Leader Facebook Connected torstan's Avatar
    Join Date
    Jul 2007
    Posts
    4,199

    Post

    Thanks for the note about the stairs. Having the walls on the grid is preferable if there's vision blocking as that can snap to grid but still leave some of the wall exposed.

    THe one thing I did notice is that with the torches snapped to grid they look a little like they are floating in mid air. Might be better to have these unsnapped so they can sit flush with the walls.

  6. #6
    Administrator Redrobes's Avatar
    Join Date
    Dec 2007
    Location
    England
    Posts
    7,244
    Blog Entries
    8

    Post

    Thats me being a bit lazy. I can put them anywhere. What they need is a torch sconce

    Heres a pic of bits were talking about. I have some doors on here too cos we found that a door in the arch looks great and better than a simple door on its own. Also you can open them too.
    Attached Images Attached Images

  7. #7
    Community Leader Facebook Connected torstan's Avatar
    Join Date
    Jul 2007
    Posts
    4,199

    Post

    Got you. Yes, the doors do look better in the arches - though they do need resized to do that nicely in general. Those pre-composited ones work really well.

    As for the walls and the stairs - I place the stairs on the bottom and lay the wall over the top. Ideally the walls have the highest z-ordering of all objects. That gets around the issues, and avoids the issue of stairs being over the wall shadow, or the straight edge of the stairs not quite lining up with the irregular edge of the wall.

  8. #8
    Community Leader Facebook Connected Steel General's Avatar
    Join Date
    Jun 2008
    Location
    Ft. Wayne, IN
    Posts
    9,530

    Default

    Welcome Aboard maxboy!

    Nice little dungeon, great use of Torstan's tiles.
    My Finished Maps | My Challenge Maps | Still poking around occasionally...

    Unless otherwise stated by me in the post, all work is licensed under a Creative Commons Attribution-Noncommercial 3.0 United States License.



  9. #9
    Community Leader Guild Sponsor Gidde's Avatar
    Join Date
    May 2009
    Location
    Michigan, USA
    Posts
    3,673

    Default

    That looks great! Welcome to the guild

  10. #10
    Professional Artist Facebook Connected Coyotemax's Avatar
    Join Date
    Jul 2009
    Location
    Canada
    Posts
    1,945

    Default

    Maxboy: I'm actually putting together a psd file for photoshop users (might work with gimp too) that drops everything right along 100x100 grid lines.

    I've got the walls done right now, I might leave the objects as they are for greater ease in positioning. As soon as I'm done my current map I'll go about making it available for upload.

    My finished maps
    "...sometimes the most efficient way to make something look drawn by hand is to simply draw it by hand..."

Page 1 of 4 1234 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •