Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: United Island's States (UIS)

  1. #1
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Wip United Island's States (UIS)

    I'd like to re-born a very old map of mine.
    It shows a fictional federal state island, called UIS, placed SE of real Newfoundland.

    I firstly drew this one in the '80s (was it summer 1985?... I don't remember exactly, I was very young) using A4 size sheets, pencils and pens. Then I joined all sheets together with scotch tape, to make a big map: so those dark strips are explained...
    Now I'm using DraftSight to make vector data, then I'll put them in Quantum GIS to have a DEM and a complete map. At last I'll probably use GIMP to refine my work.
    I'll modify some features of the original map, specially contour lines, because they didn't satisfy me.

    These examples show at most one of the six federal states, called New Pantheky, which is placed in the SW peninsula.
    The projection I use is Transverse Mercator WGS84 zone 22N. Each grid square is 10 km wide.

    New Pantheky 00.jpg
    Original hand-drawn map.

    New Pantheky 01.jpg
    Drawing vector data on raster image...

    New Pantheky 02.jpg
    Actual vector data.

    P.S. Sorry if I make some mistake in english: my mother tongue is italian.
    Last edited by AzurePlanet; 01-05-2013 at 10:22 PM.

  2. #2

    Default

    This is outta my league software wise, but its looking good so far. You seem to have been able to transfer the hand drawn elements and they look good.

  3. #3
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Default

    Quote Originally Posted by Vellum View Post
    ... You seem to have been able to transfer the hand drawn elements ...
    Yes, but unforunately it's not an automatic procedure: I'm just re-drawing over hand-made stuff, and it takes a lot of time...
    I use a CAD software because currently I can't use graphics softwares very well.

  4. #4
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Default

    The work is (very slowly) going on.

    New Pantheky 03.jpg
    Current vector data.

    I also drew the National Flag and those of the six States. I'm going to use them in the finished map.
    According to ManOfSteel's useful advice, I renamed the Nation as "United States of Newfoundislands" (USN).

    USN Bandiere 02.jpg

    Your opinions and suggestions are welcome!
    Last edited by AzurePlanet; 01-25-2013 at 03:39 AM.

  5. #5
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Default

    I've just done some experiments to create DTMs.

    Prova DTM 01.jpg

    Inside the red box there is a resolution of 20 m per pixel, with shadows, outside 80 m per pixel (very rough...).
    I used GRASS GIS to get the DTMs, unfortunally I was not able to get them by Quantum GIS.

    My final map will have a scale of 1:200000, so I think that the 20 m resolution will work well.

    Please, let me know what do you think about.

  6. #6
    Guild Adept Naeddyr's Avatar
    Join Date
    Jun 2008
    Location
    Finland
    Posts
    300

    Default

    Very, very nice, looking forward to seeing the rest.

  7. #7
    Guild Applicant
    Join Date
    Apr 2013
    Location
    St. Paul, MN
    Posts
    4

    Default

    Nice! What are you planning on using this map for?

  8. #8
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Default

    @ thes33:
    Oh, I'm just doing this map in my spare time, without a real porpouse.

  9. #9
    Guild Journeyer AzurePlanet's Avatar
    Join Date
    Dec 2012
    Location
    Italy, 43°28'N 11°09'E
    Posts
    178
    Blog Entries
    2

    Default

    Hello everyone!
    Just an update to remind me that this work is still in progress... I'm struggling with that never-ending contour lines.
    Well, to be honest, I'm a bit lazy. I carry on this work when I'm in the right mood only.

    Attachment 67236

    This is the complete site, however a lot of work has still to be done.
    Any comment/suggestion is highly appreciated.
    Attached Images Attached Images

  10. #10
    Guild Apprentice
    Join Date
    Jun 2012
    Posts
    47

    Default

    So are you hand drawing all the contours over an older raster image? It seems like you have already broken the back of it with only some inland sections left. I find the less wiggly contours to be less fun
    What are your plans for presentation? The current multi-coloured setup makes it look very much like a technical map or schematic. Will it stay this way?
    The different elements so far look extremely convincing, especially given you're hand drawing them.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •