LMAO, that sounds like a damn cool idea. Although not for this. This building sits inside a small town, so although it's well built, and defendable, it doesn't need to be too extreme.
LMAO, that sounds like a damn cool idea. Although not for this. This building sits inside a small town, so although it's well built, and defendable, it doesn't need to be too extreme.
Here's my version of it as a step by step:
The steps are:
1. Create a selection that encompasses the region that you want the earthworks in. Here I got all your outer wall outline and expanded by about 100px to get the outer edge. For the inner edge I did the same and expanded the selection by about 10px.
2. On a new layer fill the region outside the eathworks with 50% grey. Fill the inside region with black (this will ensure you have a steeper edge inside the earthworks than outside. In gimp I'd do this by creating a new selection that runs down the middle of your earthworks (so outline of walls +55px in this case) and fill inside with black, outside with grey. Then take your earthworks selection and use the gradient tool set to shaped spherical, and the gradient type to foreground to transparent with a foreground colour of white. Apply the gradient to your selection (click and drag) and you should get something like 2 for this layer.
3. Create a new layer and fill it with 50% grey. Go to Filters->Map->Bump Map. In the Bump map drop down, select the layer that looks like 2 (the black white and grey image). Fiddle with depth and angle of light until you get something you like. Apply the filter. Now this layer probably has jagged artefacts on it, so it's probably worth applying a 5-10px Gaussian blur on it to smooth those out.
4. Change the blend mode of this layer to overlay or soft light and make sure it's over your grass layer. Fiddle with the opacity until you're happy with it. You can also duplicate the layer and set the blend mode to darken only to bump up the shadows. Make sure the layer that I have as 2 in the walk through is turned off - you won't need that again.
You can then go on to add erosion effect to your overlay layer, but that should give you the basic structure of your berm. Remember that your walls are going to cast shadows too - so you'll need to alter your overlay layer to show that as you go forward.
Ok, it's taken a while, and a *lot* of attempts, but I have something, I'm almost happy with now.....
I've followed Torstan's instructions above, but actually done two bump maps, and merged them, each slightly differently spaced and set. Gives a more natural feel I think. I've also opened up the entrances.
Or with shadows:
Next steps are to try and get the cobbles-> dirt merging, and possibly some cart tracks
Looking good. One note - when you're doing the shadows for the walls you have them as an all round glow. However the berm is lit from the NW. To be consistent the walls whould be throwing the shadows to the SE. You might want to moe the shadows SE a little. I'd also lighten the wall shadow a bit - it's much heavier than the other shadows.
Coming along nicely.
I thought you'd pick up on the shadows Torstan!
I will probably redo the shadow layer for the walls, I did it before the berm, and although I like the effect it gives of a deep pit right around, it does need some work.
One question, as I did the berm mostly by rote, following your instructions...If I'd wanted this to be lit from say the East, how would I achieve that? Is it to do withe the way the spherical gradient is applied?
Nope, the difference comes when you apply the bevel filter. In there you'll find a lighting angle control where you can set the direction of the light source.
If you like the deeper pit effect, then keep that bit and erase the rest of the shadow. Then re-do the overall shadow on another layer. Have a play with different blend modes as well for your shadow layer - low opacity and multiply, or full opacity soft light/overlay layers (in gimp soft light and overlay are the same thing - not so in other apps).
Latest WIP. I've got the main building in now, to stop it looking quite so empty, there will be a well, and a couple of other building to follow.
I've also hand extended the mound out by the front gates, to give the effect of a channel, funnleing people in the right way. Not quite happy with it yet, but it's coming along.
This map making doesn't half take some time!
Posting Permissions
Reply With Quote
